Differences between revisions 68 and 74 (spanning 6 versions)
Revision 68 as of 2011-12-18 23:26:23
Size: 8581
Editor: BobAdamson
Comment:
Revision 74 as of 2013-09-13 15:21:23
Size: 9022
Editor: NickBannon
Comment: New triplc.com URL
Deletions are marked like this. Additions are marked like this.
Line 19: Line 19:
||1||manual drop button|| || || || ||
||1 (./) ||PLC||brain||FMD88-10 starter kit, i-STK88-10, http://www.tri-plc.com/ISTK-FMD88-10.htm (including http://www.tri-plc.com/fmd88-10.htm , software, data cable) || || $475 kit ||
||1 (./) ||PLC expansion card||additional IO||EXP1616R, http://www.tri-plc.com/exp1616r.htm || || kit ||
||1 (./) ||manual drop button|| --(reuse old button)-- new button bought from altronics|| || || ||
||1 (./) ||PLC||brain||FMD88-10 starter kit, i-STK88-10, http://www.tri-plc.com/ISTK-FMD88-10.htm (including http://www.triplc.com/fmd8810.htm , software, data cable) || || $475 kit ||
||1 (./) ||PLC expansion card||additional IO||EXP1616R, http://www.triplc.com/exp1616r.htm || || kit ||
Line 27: Line 27:
|| ||cable ties|| || || Donation? || || || (./) ||reuseable cable ties|| || || Altronics || ||
Line 29: Line 29:
|| ||terminal blocks|| || || || || || (./)||terminal blocks|| ||Altronics (see below) || || ||
Line 41: Line 41:
||1 ||putty/sealant|| put in corners so water can't sit there and cause rust|| || || || ||1 (./) ||putty/sealant|| put in corners so water can't sit there and cause rust|| || || ||
Line 45: Line 45:
 * 10x24V DC input for can sensing (would it be worth multiplexing this?)
 * 7x24V DC input for front door buttons (ditto with the multiplexing question)
 * 10x24V DC input for can sensing
 * 7x24V DC input for front door buttons
Line 48: Line 48:
 * 10x100V AC relay outputs
 * 7x DC outputs for empty slot display
 * 10x110V AC relay outputs
 * 7x 5V DC outputs for empty slot display
Line 63: Line 63:
  * End clamp   * Earth (green/yellow) doubles as end clamp
Line 65: Line 65:
  * 6 for 24V power positive and negative (3 red, 3 black) - 2 PLC, 2 fans, 2 expansion board   * 3 red - 24V power distribution positive (bridged)
  *
3 black - 24V power distribution ground (bridged)
Line 67: Line 68:
  * 20 for slot microswitches (10 red, 10 black)   * 10 red - slot microswitches positive
 * 10 black - slot microswitch ground (bridged)
Line 69: Line 71:
  * 20 for slot solenoids (10 brown, 10 blue)   * 10 grey - solenoid active
  * 10 blue - solenoid neutral (bridged)
Line 71: Line 74:
  * 8 for 110V distribution (4 brown, 4 blue) - 4 for relay board, 2 for 24V supply input, 2 for 5V supply input
  * Partition
  * 3 for earth (green/yellow) - 1 for PLC, 1 for 24V supply, 1 for 5V supply
  * End cap
  * End clamp
  * 4 grey - 110V power distribution active (bridged)
  * 4 blue - 100V power distribution neutral (bridged)
  * 2 earth (green/yellow) doubles as end clamp
Line 86: Line 87:
 * 14 brown  * 14 grey
Line 92: Line 93:
 * 8 shorting links  * 8 shorting links (2 of each colour)
Line 123: Line 124:
 * The crimps on the fan loom where two wires go into a crimp should be replaced with the bigger blue crimps instead of the small red ones (you'll need 2 blue female 4.8mm and two male 4.8mm)
Line 125: Line 125:
 * --(small can support)-- Done! A small bracket has been made which can fit on any of the front slots. Ask BobAdamson how to use it.
 * coin return magic
 * coin counter
 * more LEDs, not blue
 * redo fan wiring (again)
 * front perspex lights
 * screens
 * button screens
 * --(snack machine keypad, 3 key needs more debouncing)-- Sortof done. BobAdamson pulled it apart and cleaned the contacts. It could probably do with some small capacitors across each button if it keeps happening.
 * documentation and all code up-to-date in ~coke

Aims

  • redo all internal wiring and logic, except the refrigeration parts
  • make the machine more safe by doing things properly and reducing the voltage of exposed components
  • keep the software interface as simple or more simple than before
  • make the buttons on the front of the machine work for dispense
  • make it extensible so things can be added on
  • give the machine a general service where necessary (seals, rust protection, oil)

Draft Bill of Materials

Amount

Item

Use

Model

Unit Cost

Total

7 (./)

microswitches

front button switches, 2.21N

au.element14.com

$2.16

$15.12

20 (./)

microswitches

each slot has double microswitches, there are 10 slots, 0.15N

au.element14.com

$3.60

$72

7 (./)

5mm round white LED's

replace empty slot globes

Standard 5mm LEDs, au.element14.com White? Or red for empty, green for non-empty?

0.616

$6.16

7

resistors

empty slot LED protection

< $0.05

1

stripboard or veroboard

mount LED resistors

10 (./)

4 pin connectors

one for each slot actuator unit

Molex mini-fit jr series 4way connectors Also compatible

$31.26

1 (./)

9 pin connector

interface with distribution box

recycle old connector

free

1 (./)

manual drop button

reuse old button new button bought from altronics

1 (./)

PLC

brain

FMD88-10 starter kit, i-STK88-10, http://www.tri-plc.com/ISTK-FMD88-10.htm (including http://www.triplc.com/fmd8810.htm , software, data cable)

$475 kit

1 (./)

PLC expansion card

additional IO

EXP1616R, http://www.triplc.com/exp1616r.htm

kit

1 (./)

24V PSU

kinda need a power supply

automationmart.com

kit

1 (./)

5V PSU

led power and future expansion power

INA Solutions

62.83

62.83

42m (./)

4 core wire, 1mm minimum diameter (to carry 2A), 18AWG

actuator and empty switch wiring

http://www.altronics.com.au/index.asp?area=item&id=W3121

$1.22/m

$51.63

11m (./)

9 core wire

front buttons and lights wiring

http://www.altronics.com.au/index.asp?area=item&id=W2712

43c/m

$4.72

5m (./)

2 core wire

refrigeration fan power

http://www.altronics.com.au/index.asp?area=item&id=W2139

80c/m

$4.00

(./)

reuseable cable ties

Altronics

10m (./)

cable loom

cable loom for fans and actuators

http://www.altronics.com.au/index.asp?area=item&id=H3814

$12.90

$12.90

(./)

terminal blocks

Altronics (see below)

3 (./)

galvanising paint

recoating everything

Dy-Mark Zinc Gal from Bunnings

$13.95

$13.95

1 (./)

pack 100 female quick connectors 4.8mm

attach to microswitches

http://www.altronics.com.au/index.asp?area=item&id=H1992A

$11.35

$11.35

1 (./)

pack 100 bullet male connectors

cable loom

http://www.altronics.com.au/index.asp?area=item&id=H2152A

$8.13

$8.13

1 (./)

pack 100 bullet female connectors

cable loom

http://www.altronics.com.au/index.asp?area=item&id=H2122A

$13.08

$13.08

1 (./)

pack 100 terminal pin connectors

terminal block

http://www.altronics.com.au/index.asp?area=item&id=H1902

$8.34

$8.34

1 (./)

pack 10 male quick connectors 4.8mm

fridge fans

http://www.altronics.com.au/index.asp?area=item&id=H1851

$2.90

$2.90

3 (./)

Fans to replace refrigeration fans

24V Altronics

$11.07

$33.21

3 (./)

Finger guards

base refrigeration fan covers

$1.09

$3.27

12 (./)

sheet metal screws

attach fans to cooler cover

60 (./)

2mm spacers (washers?)

otherwise fans will jam on lip of cover

1 (./)

electrical tape (white)

$1.55

$1.55

1 (./)

putty/sealant

put in corners so water can't sit there and cause rust

Total

Internal PLC IO Requirements

  • 10x24V DC input for can sensing
  • 7x24V DC input for front door buttons
  • 1x24V DC input for manual dispense mode button
  • 10x110V AC relay outputs
  • 7x 5V DC outputs for empty slot display

Process

  • empty the machine and bring it into the clubroom. This means everything won't have to be packed up at the end of the day while we're working on it
  • remove one of the stacks and test a slot actuator to see what it runs off. This determines what hardware we use to drive everything, so we need to know.
  • purchase all required hardware (PLC, wiring, connectors, switches, etc.)
  • write software (state machine based programming implemented in ladder logic, should be quite trivial)

  • wire up on the bench and test
  • service the machine. A can of zinc spraypaint wouldn't go astray on some of the rust spots I think. Check all the seals. Oil what needs oiling. Clean what needs cleaning.
  • install everything into the machine and test

Wiring it up

  • Terminal Blocks
    • Earth (green/yellow) doubles as end clamp
    • End cap
    • 3 red - 24V power distribution positive (bridged)
    • 3 black - 24V power distribution ground (bridged)
    • Partition
    • 10 red - slot microswitches positive
    • 10 black - slot microswitch ground (bridged)
    • Partition
    • 10 grey - solenoid active
    • 10 blue - solenoid neutral (bridged)
    • Partition
    • 4 grey - 110V power distribution active (bridged)
    • 4 blue - 100V power distribution neutral (bridged)
    • 2 earth (green/yellow) doubles as end clamp
  • Commoning bars/shorting links (come in strips of ten that you can cut to length)
    • 8 (7 plus one spare)
  • Din rail
    • 2m
  • Slotted duct 3 metres

Total Order:

  • 13 red
  • 13 black
  • 14 grey
  • 14 blue
  • 3 green/yellow
  • 2 end caps
  • 2 end clamps
  • 4 partitions
  • 8 shorting links (2 of each colour)
  • 2m din rail
  • 1 Label set numbers 1 to 50
  • Network cable connection
    • Panduit CFPHS2IW Faceplate or similar
    • Panduit Cat 6 Mech and cable

Measured things

  • Can drop process: 400ms on, 500ms off, 660ms on, 300VAC peak-to-peak, 1.8A
  • Wire lengths:
    • Actuator units 0,1,2,3: 80cm actuator to wire harness, 210cm harness to corner of machine door, 40cm up door, 45cm across, 40cm up to terminal block (4-core minimum) (16.6m)
    • Actuator units 4,5: 80cm actuator to wire harness, 170cm harness to corner of machine door, 40cm up door, 45cm across, 40cm up to terminal block (4-core minimum) (7.5m)
    • Actuator units 6,7,8,9: 80cm actuator to wire harness, 140cm harness to corner of machine door, 40cm up door, 45cm across, 40cm up to terminal block (4-core minimum) (13.8m)
    • Buttons: 75cm across front of door, 60cm down edge of door, 45cm across, 40cm up to terminal block (8-core minimum) (2.2m)
    • Lights: 75cm across front of door, 60cm down edge of door, 45cm across, 40cm up to terminal block (8-core minimum) (2.2m)
  • The fans suck air through the fridge unit, they don't blow it
  • Plug coming from the back of the distrubution box (red 9 way):
    • Brown/White 110V
    • Blue/White Neutral
    • Red/White 100V

Extra Things To Consider

Stuff to fix in future

  • The 5x1mm washers acting as spacers for the bottom refigeration fans should be replaced with a 5mm spacer or piece of pipe instead - the washers will be impossible to put back on if the fans ever need to be removed
  • small can support Done! A small bracket has been made which can fit on any of the front slots. Ask BobAdamson how to use it.

  • coin return magic
  • coin counter
  • more LEDs, not blue
  • redo fan wiring (again)
  • front perspex lights
  • screens
  • button screens
  • snack machine keypad, 3 key needs more debouncing Sortof done. BobAdamson pulled it apart and cleaned the contacts. It could probably do with some small capacitors across each button if it keeps happening.

  • documentation and all code up-to-date in ~coke