|
Size: 1361
Comment:
|
Size: 2316
Comment: Fixed random text
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 19: | Line 19: |
| Bitumen current runs Cisco IOS v12.2 | Bitumen currently runs Cisco IOS v12.2. |
| Line 23: | Line 23: |
| 2x SupIV Supervisors 2x 6 port GBIC cards 2x 24 port GigE cards 1x 48 port GigE card |
* Cisco Catalyst 4507R Chassis * 2x WS-X4515 Supervisor Engine IV * 2x WS-X4306-GB Gigabit Ethernet Module, 6-Ports (GBIC) * 2x WS-X4424-GB-RJ45 24-port 10/100/1000 Module (RJ45) * 1x WS-X4448-GB-RJ45 48-port 10/100/1000 Module (RJ45) |
| Line 36: | Line 37: |
| '''Configuring a port''' | '''Configuring an access layer port''' |
| Line 44: | Line 45: |
| bitumen(config-if#no shut bitumen(config-if)#end |
bitumen(config-if)#no shut bitumen(config-if)#exit |
| Line 47: | Line 48: |
| }}} ''no shut'' enables the port, ''shut'' disables '''Configuring a trunk port''' The native vlan setting here is only required if you plan on sending untagged packets from the device across the link, you can leave it out otherwise. Similarly, you can leave out the allowed vlan command if you're happy for it to trunk any and every vlan. {{{ bitumen>en bitumen#conf t Enter configuration commands, one per line. End with CNTL/Z. bitumen(config)#int Gi7/2 bitumen(config-if)#switchport trunk encapsulation dot1q bitumen(config-if)#switchport mode trunk bitumen(config-if)#switchport trunk native vlan 8 bitumen(config-if)#switchport trunk allowed vlan 2,3,421 bitumen(config-if)#description A trunk port bitumen(config-if)#exit bitumen(config)#write mem |
Bitumen refers to bituminous sands, which are a type of petroleum deposit.
History prior to arriving to UCC
The switch lived a happy life with Apache Energy in Perth.
UCC history
Not a lot of history yet!
Current tasks
Core switch/router
Current software configuration
Bitumen currently runs Cisco IOS v12.2.
Current hardware configuration
- Cisco Catalyst 4507R Chassis
- 2x WS-X4515 Supervisor Engine IV
- 2x WS-X4306-GB Gigabit Ethernet Module, 6-Ports (GBIC)
- 2x WS-X4424-GB-RJ45 24-port 10/100/1000 Module (RJ45)
- 1x WS-X4448-GB-RJ45 48-port 10/100/1000 Module (RJ45)
Future plans for the machine
Given Bitumen has full Layer 3 capacity, potentially moving all NAT, firewall etc to it
Useful commands when working with Bitumen
More for Wheel than anyone else, the following might be considered useful
Configuring an access layer port
bitumen>en bitumen#conf t Enter configuration commands, one per line. End with CNTL/Z. bitumen(config)#int Gi7/2 bitumen(config-if)#switchport description demo bitumen(config-if)#switchport access vlan 3 bitumen(config-if)#no shut bitumen(config-if)#exit bitumen#write mem
no shut enables the port, shut disables
Configuring a trunk port
The native vlan setting here is only required if you plan on sending untagged packets from the device across the link, you can leave it out otherwise. Similarly, you can leave out the allowed vlan command if you're happy for it to trunk any and every vlan.
bitumen>en bitumen#conf t Enter configuration commands, one per line. End with CNTL/Z. bitumen(config)#int Gi7/2 bitumen(config-if)#switchport trunk encapsulation dot1q bitumen(config-if)#switchport mode trunk bitumen(config-if)#switchport trunk native vlan 8 bitumen(config-if)#switchport trunk allowed vlan 2,3,421 bitumen(config-if)#description A trunk port bitumen(config-if)#exit bitumen(config)#write mem
Thanks to:
Brad Peczka for acquiring for the club via his employer, Apache Energy Limited (to whom we are very grateful), then delivering and configuring with UCC members. [MRD], [DTK] and [CJS] for re-racking and re-patching.
