Differences between revisions 6 and 18 (spanning 12 versions)
Revision 6 as of 2012-07-10 16:17:47
Size: 2151
Editor: BradPeczka
Comment:
Revision 18 as of 2017-08-06 21:31:12
Size: 3355
Editor: DavidAdam
Comment:
Deletions are marked like this. Additions are marked like this.
Line 19: Line 19:
Bitumen currently runs Cisco IOS v12.2. Bitumen currently runs Cisco IOS 12.2(54)SG1.

[[https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/54sg/configuration/guide/config.html|Catalyst 4500 Series Switch Software Configuration Guide, 12.2(54)SG]]
Line 37: Line 39:
'''Showing port names'''

If you're looking for a port that has already been configured and named:
{{{
bitumen>en
bitumen#show int description
or
bitumen#show int status
}}}
Or if you've set up a linux machine and want to know what port it's plugged into, install ladvd on the machine, and then run the following on bitumen (pay attention to the spelling of neighbors, or just shorten it to neigh):
{{{
bitumen>en
bitumen#show cdp neighbors
}}}
Line 43: Line 60:
bitumen(config-if)#switchport description demo bitumen(config-if)#description demo
Line 47: Line 64:
bitumen(config)#exit
Line 54: Line 72:
The native vlan setting here is only required if you plan on sending untagged packets from the device across the link, you can leave it out otherwise The native vlan setting here is only required if you plan on sending untagged packets from the device across the link, you can leave it out otherwise. Similarly, you can leave out the allowed vlan command if you're happy for it to trunk any and every vlan.
Line 64: Line 82:
bitumen(config-if)#switchport trunk allowed vlan 2,3,421
Line 66: Line 85:
bitumen(config)#write mem bitumen(config)#exit
bitumen#write mem
}}}

To show the allowed VLANs on a trunk
{{{
bitumen>en
bitumen#show int gi5/23 switchport
}}}

To add an allowed VLAN to a trunk (this example adding VLAN 4 to port 5/23)
{{{
bitumen>en
bitumen#conf t
bitumen(config)#int gi5/23
bitumen(config-if)#switchport trunk allowed vlan add 4
bitumen(config-if)#exit
bitumen(config)#exit
bitumen#write mem

Bitumen refers to bituminous sands, which are a type of petroleum deposit.

History prior to arriving to UCC

The switch lived a happy life with Apache Energy in Perth.

UCC history

Not a lot of history yet!

Current tasks

Core switch/router

Current software configuration

Bitumen currently runs Cisco IOS 12.2(54)SG1.

Catalyst 4500 Series Switch Software Configuration Guide, 12.2(54)SG

Current hardware configuration

  • Cisco Catalyst 4507R Chassis
  • 2x WS-X4515 Supervisor Engine IV
  • 2x WS-X4306-GB Gigabit Ethernet Module, 6-Ports (GBIC)
  • 2x WS-X4424-GB-RJ45 24-port 10/100/1000 Module (RJ45)
  • 1x WS-X4448-GB-RJ45 48-port 10/100/1000 Module (RJ45)

Future plans for the machine

Given Bitumen has full Layer 3 capacity, potentially moving all NAT, firewall etc to it

Useful commands when working with Bitumen

More for Wheel than anyone else, the following might be considered useful

Showing port names

If you're looking for a port that has already been configured and named:

bitumen>en
bitumen#show int description
or
bitumen#show int status

Or if you've set up a linux machine and want to know what port it's plugged into, install ladvd on the machine, and then run the following on bitumen (pay attention to the spelling of neighbors, or just shorten it to neigh):

bitumen>en
bitumen#show cdp neighbors

Configuring an access layer port

bitumen>en
bitumen#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
bitumen(config)#int Gi7/2
bitumen(config-if)#description demo
bitumen(config-if)#switchport access vlan 3
bitumen(config-if)#no shut
bitumen(config-if)#exit
bitumen(config)#exit
bitumen#write mem

no shut enables the port, shut disables

Configuring a trunk port

The native vlan setting here is only required if you plan on sending untagged packets from the device across the link, you can leave it out otherwise. Similarly, you can leave out the allowed vlan command if you're happy for it to trunk any and every vlan.

bitumen>en
bitumen#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
bitumen(config)#int Gi7/2
bitumen(config-if)#switchport trunk encapsulation dot1q
bitumen(config-if)#switchport mode trunk
bitumen(config-if)#switchport trunk native vlan 8
bitumen(config-if)#switchport trunk allowed vlan 2,3,421
bitumen(config-if)#description A trunk port
bitumen(config-if)#exit
bitumen(config)#exit
bitumen#write mem

To show the allowed VLANs on a trunk

bitumen>en
bitumen#show int gi5/23 switchport

To add an allowed VLAN to a trunk (this example adding VLAN 4 to port 5/23)

bitumen>en
bitumen#conf t
bitumen(config)#int gi5/23
bitumen(config-if)#switchport trunk allowed vlan add 4
bitumen(config-if)#exit
bitumen(config)#exit
bitumen#write mem

Thanks to:

Brad Peczka for acquiring for the club via his employer, Apache Energy Limited (to whom we are very grateful), then delivering and configuring with UCC members. [MRD], [DTK] and [CJS] for re-racking and re-patching.


CategoryMachines