Differences between revisions 16 and 17
Revision 16 as of 2010-02-12 10:32:24
Size: 3253
Editor: TPG
Comment: Fixed formatting on table
Revision 17 as of 2011-05-08 16:18:51
Size: 1172
Editor: motsugo
Comment:
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:

== Lorenzo ==

SSH to it by hostname (lorenzo.ucc.asn.au) or IP (192.168.2.11). Uses its own set of passwords, so if you don't already have an account on it you'll have to ask someone who does to create one for you. Use 'show int status' to get started.

Lorenzo has eight broken interfaces. You can tell which ones are broken because they are filled with silicon filler, though this is an effect rather than a cause.
Line 11: Line 5:
Can only be configured by via web interface, which is at [[http://curviceps.ucc.gu.uwa.edu.au]]. This is on the management VLAN, which is only routed from inside the UCC. Can only be configured by via web interface, which is at [[http://curviceps.ucc.gu.uwa.edu.au]]. This is on the management VLAN, which is only routed from inside the UCC. If at all possible, any machines on this switch should have lldpd installed so it's easier to tell what ports they're connected to.
Line 13: Line 7:
== Olive == == Coconut ==
Line 15: Line 9:
Telnet to it by hostname (olive.ucc.asn.au) or IP (130.95.13.5). Uses its own set of passwords, so if you don't already have an account on it you'll have to ask someone who does to create one for you. Try to use Lorenzo instead if at all possible, there is a vague plan to retire Olive once everything is off it. Use 'show int status' to get started.

{{{
Port Name Status Vlan Duplex Speed Type
------- ------------------ ------------ -------- ------ ------- ----
Fa0/1 Unused disabled 3 Auto Auto 100BaseTX/FX
Fa0/2 Unused notconnect 8 Auto Auto 100BaseTX/FX
Fa0/3 Unused connected trunk A-Full A-100 100BaseTX/FX
Fa0/4 Unused notconnect 2 Auto Auto 100BaseTX/FX
Fa0/5 Unused notconnect 2 Auto Auto 100BaseTX/FX
Fa0/6 Unused notconnect 3 Auto Auto 100BaseTX/FX
Fa0/7 Unused notconnect 2 Full Auto 100BaseTX/FX
Fa0/8 Unused notconnect trunk Auto Auto 100BaseTX/FX
Fa0/9 Unused notconnect 2 Auto Auto 100BaseTX/FX
Fa0/10 Unused notconnect 3 Auto Auto 100BaseTX/FX
Fa0/11 Lorenzo (temp) notconnect trunk Auto Auto 100BaseTX/FX
Fa0/12 Unused disabled trunk Auto Auto 100BaseTX/FX
Fa0/13 Flying switch notconnect 3 Auto Auto 100BaseTX/FX
Fa0/14 evil notconnect trunk Auto Auto 100BaseTX/FX
Fa0/15 Pitch notconnect 3 Auto Auto 100BaseTX/FX
Fa0/16 Unused notconnect 3 Auto Auto 100BaseTX/FX
Fa0/17 Adrian's Server (m notconnect 3 Auto 100 100BaseTX/FX
Fa0/18 UGG AP (802.11g) notconnect 6 Auto Auto 100BaseTX/FX
Fa0/19 Madako notconnect 13 Auto Auto 100BaseTX/FX
Fa0/20 Uplink (Guild) notconnect trunk Auto Auto 100BaseTX/FX
Fa0/21 Uplink (Loft) notconnect 5 Auto Auto 100BaseTX/FX
Fa0/22 Dagon notconnect 2 Full 10 100BaseTX/FX
Fa0/23 Bench port 6 notconnect 3 Full 100 100BaseTX/FX
Fa0/24 Loftnet Spare notconnect 3 Auto Auto 100BaseTX/FX
}}}
Coconut is a Cisco 2948G running CatOS. It's configured by telnetting to coconut.ucc.gu.uwa.edu.au from inside the UCC network. Coconut's config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]]
Line 50: Line 15:
== Palm ==

The same model as Coconut, this switch is only used for LAN's. Every port is set to vlan 5, except port 1 which is a trunk port for connecting the loft cable. When it's connected to the network, you can telnet to it on palm.ucc.gu.uwa.edu.au. Its config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]]

Curviceps

Can only be configured by via web interface, which is at http://curviceps.ucc.gu.uwa.edu.au. This is on the management VLAN, which is only routed from inside the UCC. If at all possible, any machines on this switch should have lldpd installed so it's easier to tell what ports they're connected to.

Coconut

Coconut is a Cisco 2948G running CatOS. It's configured by telnetting to coconut.ucc.gu.uwa.edu.au from inside the UCC network. Coconut's config can also be seen at http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/

Alloy

Not used anymore, except for LANs. The default IP of the Alloy, contrary to what the manual says, is 192.168.1.1. The default password is 'admin'.

Palm

The same model as Coconut, this switch is only used for LAN's. Every port is set to vlan 5, except port 1 which is a trunk port for connecting the loft cable. When it's connected to the network, you can telnet to it on palm.ucc.gu.uwa.edu.au. Its config can also be seen at http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/


CategorySystemAdministration