Differences between revisions 17 and 21 (spanning 4 versions)
Revision 17 as of 2011-05-08 16:18:51
Size: 1172
Editor: motsugo
Comment:
Revision 21 as of 2019-12-02 23:00:36
Size: 2312
Editor: JamesArcus
Comment: Reflect that Kerosene has taken Bitumen's place
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:

== Kerosene ==
[[Kerosene]] is a Cisco Catalyst 4506-E running IOS (the *real* IOS, not the one made by the fruity company). It's configured by SSHing to kerosene.ucc.gu.uwa.edu.au from inside the UCC network. Kerosene's config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]]
 * All wall ports in the clubroom are connected through Kerosene
 * The gigabit uplink goes through Kerosene to a separate gigabit port on [[Murasoi]]
 * There are no POE modules installed, but we could probably get some
 * Kerosene is very heavy

== Bitumen ==

[[Bitumen]] is an old Cisco Catalyst 4507R running IOS that was previously in the place of Kerosene. The config of Kerosene was lifted nearly 1:1 from Bitumen when they were swapped, only remapping ports between the different-sized line cards and accounting for the new 10G capability. Bitumen is also very heavy.

== Walnut ==

See [[Walnut]]. Its configuration is also accessible at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs]].
Line 5: Line 21:
Can only be configured by via web interface, which is at [[http://curviceps.ucc.gu.uwa.edu.au]]. This is on the management VLAN, which is only routed from inside the UCC. If at all possible, any machines on this switch should have lldpd installed so it's easier to tell what ports they're connected to.  [[Curviceps]] can only be configured by via web interface, which is at [[http://curviceps.ucc.gu.uwa.edu.au]]. This is on the management VLAN, which is only routed from inside the UCC. If at all possible, any machines on this switch should have either ladvd (where available) or lldpd installed so it's easier to tell what ports they're connected to.
Line 9: Line 25:
Coconut is a Cisco 2948G running CatOS. It's configured by telnetting to coconut.ucc.gu.uwa.edu.au from inside the UCC network. Coconut's config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]] [[Coconut]] is a Cisco 2948G running CatOS. It's configured by telnetting to coconut.ucc.gu.uwa.edu.au from inside the UCC network. Coconut's config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]]
 * Not in use any more, except for camps
Line 17: Line 34:
The same model as Coconut, this switch is only used for LAN's. Every port is set to vlan 5, except port 1 which is a trunk port for connecting the loft cable. When it's connected to the network, you can telnet to it on palm.ucc.gu.uwa.edu.au. Its config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]] The same model as [[Coconut]], this switch is only used for LANs. Every port is set to vlan 5, except port 1 which is a trunk port for connecting the loft cable. When it's connected to the network, you can telnet to it on palm.ucc.gu.uwa.edu.au. Its config can also be seen at [[http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/]]

Kerosene

Kerosene is a Cisco Catalyst 4506-E running IOS (the *real* IOS, not the one made by the fruity company). It's configured by SSHing to kerosene.ucc.gu.uwa.edu.au from inside the UCC network. Kerosene's config can also be seen at http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/

  • All wall ports in the clubroom are connected through Kerosene
  • The gigabit uplink goes through Kerosene to a separate gigabit port on Murasoi

  • There are no POE modules installed, but we could probably get some
  • Kerosene is very heavy

Bitumen

Bitumen is an old Cisco Catalyst 4507R running IOS that was previously in the place of Kerosene. The config of Kerosene was lifted nearly 1:1 from Bitumen when they were swapped, only remapping ports between the different-sized line cards and accounting for the new 10G capability. Bitumen is also very heavy.

Walnut

See Walnut. Its configuration is also accessible at http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs.

Curviceps

Curviceps can only be configured by via web interface, which is at http://curviceps.ucc.gu.uwa.edu.au. This is on the management VLAN, which is only routed from inside the UCC. If at all possible, any machines on this switch should have either ladvd (where available) or lldpd installed so it's easier to tell what ports they're connected to.

Coconut

Coconut is a Cisco 2948G running CatOS. It's configured by telnetting to coconut.ucc.gu.uwa.edu.au from inside the UCC network. Coconut's config can also be seen at http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/

  • Not in use any more, except for camps

Alloy

Not used anymore, except for LANs. The default IP of the Alloy, contrary to what the manual says, is 192.168.1.1. The default password is 'admin'.

Palm

The same model as Coconut, this switch is only used for LANs. Every port is set to vlan 5, except port 1 which is a trunk port for connecting the loft cable. When it's connected to the network, you can telnet to it on palm.ucc.gu.uwa.edu.au. Its config can also be seen at http://cvs.ucc.asn.au/cgi-bin/viewvc.cgi/rancid/ucc/configs/


CategorySystemAdministration