Differences between revisions 1 and 8 (spanning 7 versions)
Revision 1 as of 2010-03-15 17:04:21
Size: 951
Editor: BobAdamson
Comment: created
Revision 8 as of 2010-03-17 10:43:51
Size: 3065
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
##you can obviously change this to whatever you want and add/remove what you do/don't need, this is a draft template
##aim to add pictures, it makes things way cooler
Line 6: Line 4:
== Description ==
At some point in the past, Physics purchased an old RAN Bofors gun mount and bolted a dish to it and attached some motors and stuff to move it, but didn't succeed in writing code to control the thing. So there's a several hundred kilo gun mount sitting on the roof of Physics doing nothing, when it could be looking for UFOs or doing [[http://en.wikipedia.org/wiki/Very_Long_Baseline_Interferometry|VLBI]] on a really small scale with the other radiotelescope.
Line 7: Line 7:
== Description ==
There is a radiotelescope on the roof of physics, we're going to do stuff with it.
Mostly, it's a cool project that will require input from all members of the UCC, whether what you care about is microcontrollers, operating systems, mechatronics, data storage/analysis, or the web.
Line 10: Line 9:
It's also a great opportunity to learn about science and help out Physics, a cool but underfunded section of the University.

It's important to note that 1) The Radiotelescope will remain the property of the School of Physics and 2) We'll be giving it to them when it's 'working', along with the code to make it work and display the data.
Line 19: Line 21:
##TLA's are cool, but real names are cooler. Also mention if others are welcome to get involved, or remove this heading completely
Basically everyone.
Line 25: Line 26:
=== Overall ===
 * Initial inspection (./)
 * Find or buy the motors - [RPS] has emailed School of Physics about these
 * Talk to physics about getting a receiver installed

=== Gun mount ===
 * Give it a good lube
 * Design and build a proper base to replace the pallet - MarkTearle has some ideas
 * Test position sensors (pots)
 * Select and move to final location
 * Manually test movements (either by driving motor or with a big lever)

=== Control system ===
 * Check power supply for safety before supplying power
 * Inspect existing electronics and try to identify capabilities
 * Test existing electronics
 * Label all cables
 * Identify current remote control capabilities
 * Decide whether to use existing equipment or replace totally

=== Software ===
 * Identify control system remote capabilities
 * Look for existing control software

Line 27: Line 53:
Control chips:
 * 74LS22 - dual 4-input NAND gate
 * 7407 - Hex inverter and buffer
 * 555 - timer IC
 * 2 x LM319N - dual voltage comparitors (?wired to potentiometer)
 * LM348 - quad 741 op-amp
 * OP07CN - very low offset single bipolar op-amps

3 x relays are dual-pole, dual throw: [[http://tuvok.mitch.id.au/images/RadioTS/RadioTS 022.jpg|photo with block diagram]]

Stepper motor controller: RTA Pavia GMD 04 [[http://www.rtaeurope.com/rta/PROD/gmd.HTM|website]] [[attachment:GMD stepper motor data sheet.pdf|uninformative datasheet]]
Line 29: Line 66:

[[http://tuvok.mitch.id.au/images/RadioTS/|Photos]]

Description

At some point in the past, Physics purchased an old RAN Bofors gun mount and bolted a dish to it and attached some motors and stuff to move it, but didn't succeed in writing code to control the thing. So there's a several hundred kilo gun mount sitting on the roof of Physics doing nothing, when it could be looking for UFOs or doing VLBI on a really small scale with the other radiotelescope.

Mostly, it's a cool project that will require input from all members of the UCC, whether what you care about is microcontrollers, operating systems, mechatronics, data storage/analysis, or the web.

It's also a great opportunity to learn about science and help out Physics, a cool but underfunded section of the University.

It's important to note that 1) The Radiotelescope will remain the property of the School of Physics and 2) We'll be giving it to them when it's 'working', along with the code to make it work and display the data.

Creation date: 15 March 2010

Location of source:

Project leader

List of people involved

Basically everyone.

Project plan

Overall

  • Initial inspection (./)

  • Find or buy the motors - [RPS] has emailed School of Physics about these
  • Talk to physics about getting a receiver installed

Gun mount

  • Give it a good lube
  • Design and build a proper base to replace the pallet - MarkTearle has some ideas

  • Test position sensors (pots)
  • Select and move to final location
  • Manually test movements (either by driving motor or with a big lever)

Control system

  • Check power supply for safety before supplying power
  • Inspect existing electronics and try to identify capabilities
  • Test existing electronics
  • Label all cables
  • Identify current remote control capabilities
  • Decide whether to use existing equipment or replace totally

Software

  • Identify control system remote capabilities
  • Look for existing control software

Other info

Control chips:

  • 74LS22 - dual 4-input NAND gate
  • 7407 - Hex inverter and buffer
  • 555 - timer IC
  • 2 x LM319N - dual voltage comparitors (?wired to potentiometer)
  • LM348 - quad 741 op-amp
  • OP07CN - very low offset single bipolar op-amps

3 x relays are dual-pole, dual throw: photo with block diagram

Stepper motor controller: RTA Pavia GMD 04 website uninformative datasheet

Photos